DIY Tub Setup.
DIY Tub Setup.
Blog Article
We've uncovered the article on Installing A Bathtub down the page on the web and reckoned it made sense to share it with you here.
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is readily easily accessible, the project can relocate speedily; if you need to open a wall surface to remove the old tub and also position the new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will assist you install a new bath tub in your restroom if you have actually already purchased a new bathtub and also do not need to change the plan of your previous water supply pipes.
Your tools as well as product list need to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite problematic due to the limited accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in area in between the faucet as well as the sink. Safeguard the tap in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap ports. The former type should be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait until the bath tub has been made use of at least when as this will resolve it into its last placement.
Getting ready for the Installment
First of all, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
We were guided to that report on A Step-by-Step Guide to Installing a Bathtub through a good friend on a different web address. Are you aware of somebody else who is excited by the niche? Be sure share it. Thank you so much for your time invested reading it.
Source This Article Report this page